Skip to main content


Dynamometer for Hand Strength

Submitted by Rich on Mon, 08/13/2018 - 17:41

A PocketLab Voyager Hand Dynamometer

Hand and finger strength is vital in many aspects of life--from sports such as rock climbing to jobs including airline baggage workers.  PocketLab Voyager's tactile sensor can be used to construct a very simple hand dynamometer to measure strength of a person's hands and fingers.  Figure 1 shows a simple dynamometer constructed by the author.  It consists of a 2" x 2" x 4" block of wood to which the PocketLab tactile sensor has been attached using removable double stick poster tape.


Heel Pressure: Running versus Walking

Submitted by Rich on Fri, 08/10/2018 - 18:28

Heel Pressure

Do you really know how to walk or run?  PocketLab's tactile pressure sensor provides for an opportunity for your students to investigate foot pressure during these activities.  Improper form can ultimately lead to unwanted visits to a podiatrist.  Whenever you take a step, your body places pressure on muscles, joints and tendons in your legs, knees, ankles, feet and toes.   Controlling heel pressure is a key factor to prevent injuries in this regard.


Hysteresis of a Tactile Sensor

Submitted by Rich on Mon, 07/30/2018 - 15:38

What is hysteresis?

Hysteresis can be defined as a lag time in the response of a system to forces placed on the system.  A common way used in physics classes to observe hysteresis is by loading and then unloading weights from a suspended rubber band, while observing the extension of the rubber band.  Students find that the rubber band does not Obey Hooke's law.  They also observe that amount of stretch of the rubber band is different when unloading than when loading.

Grade Level

3D Printed Pendulum for Simple Harmonic Motion

Submitted by clifton on Mon, 07/09/2018 - 19:37

This 3D printed model demonstrates the physics of a simple pendulum that consists of a mass, m, hanging from an arm of length, L, and fixed at a pivot point, P. You can move the mass along the length of the arm to change the center of mass of the pendulum. If you displace the pendulum from equilibrium to an initial angle, θ, and release, the motion will be regular and repeat. This is an example of periodic motion also called simple harmonic motion.

Grade Level

PocketLab/Ozobot LIDAR Demonstration

Submitted by Rich on Fri, 07/06/2018 - 23:05


LIDAR—an acronym for Light Detection and Ranging—is a method for remote sensing to measure distances.  While LIDAR commonly uses reflected laser light to accomplish this, students can investigate LIDAR principles by using Voyager’s IR rangefinder in conjunction with Ozobot Evo.  Ozobot is a tiny programmable robot that can follow lines.  In this activity, PocketLab Voyager is mounted on top of Ozobot.  While Ozobot t

Grade Level

Relative Velocity Lab: PocketLab/Ozobot/LEGO

Submitted by Rich on Sat, 06/30/2018 - 19:32

Introduction to Relative Velocity

Airplanes can experience head winds or tail winds that affect their flight time.  Similarly, motorboats on a river experience ground velocities that are dependent on whether they are traveling upstream or downstream.  Both of these phenomena are associated with a physics concept known as relative velocity--the main topic of this lab.

Grade Level

PocketLab/Phyphox Damped Lissajous Figures

Submitted by Rich on Mon, 06/11/2018 - 20:33

Lissajous Introduction

Lissajous patterns have fascinated physics students for decades.  They are commonly observed on oscilloscopes by applying simple harmonic functions with different frequencies to the vertical and horizontal inputs.  Three examples are shown in Figure 1.  From left to right, the frequency ratios are 1:2, 2:3, and 3:4.  These Lissajous patterns were created by use of the parametric equation section of The Grapher software written by the author of this lesson.  You are welcome to use this softwa

Grade Level

PocketLab/Phyphox Tracer Lab

Submitted by Rich on Thu, 06/07/2018 - 18:08

Introduction to this Lab

This is a quick and fun lab for makers!  In this lab, a pair of PocketLabs and Phyphox software are used to make a tracer.  As shown in Figure 1, the pair of PocketLab Voyagers are mounted to a small movable rectangular piece of plastic, perpendicular to one another and parallel to two edges of the plastic.  A small black circle is taped to the plastic to serve as the point for following the item to be traced.  In our example, a five-pointed star is traced.  One of the Voyagers is labeled X, and it